# text: "If you would like to move your registered copy of InDisk‚Ñ¢ Labeler to a different computer, click on the \"Uninstall\" button below.\n\nThis will move the registration information to the Floppy that InDisk‚Ñ¢ Labeler is currently running from."
# item 3: TEXT (0x88) disabled
# bounds: x1=79 y1=132 x2=466 y2=197
# text: "After you Uninstall, take the Floppy to the other computer, and run InDisk‚Ñ¢ Labeler from the Floppy. Click on the \"Install\" button, then copy InDisk‚Ñ¢ Labeler from the Floppy to the other computer\'s hard disk."
DITL_130_Install alert.txt
# 3 entries
# item 0: BUTTON (0x04) enabled
# bounds: x1=391 y1=92 x2=449 y2=112
# text: "Cancel"
# item 1: BUTTON (0x04) enabled
# bounds: x1=309 y1=92 x2=374 y2=112
# text: "Install"
# item 2: TEXT (0x88) disabled
# bounds: x1=79 y1=18 x2=455 y2=52
# text: "Click the \"Install\" button below to install your registered copy of InDisk‚Ñ¢ Labeler on this computer."
# text: "Concept and Program Design by:\n Warren Schroeder"
# item 8: TEXT (0x08) enabled
# bounds: x1=189 y1=132 x2=421 y2=148
# text: "InDisk is a trademark of Spectrum"
# item 9: TEXT (0x08) enabled
# bounds: x1=18 y1=111 x2=161 y2=126
# text: "The Labeless-Labeler"
# item 10: TEXT (0x88) disabled
# bounds: x1=209 y1=161 x2=393 y2=178
# text: "Click anywhere to continue"
# item 11: TEXT (0x08) enabled
# bounds: x1=23 y1=132 x2=87 y2=148
# text: "Serial # A"
# item 12: TEXT (0x08) enabled
# bounds: x1=86 y1=132 x2=166 y2=148
# text: ""
# item 13: TEXT (0x08) enabled
# bounds: x1=51 y1=285 x2=127 y2=305
# text: "REGISTERED"
# item 14: TEXT (0x08) enabled
# bounds: x1=55 y1=176 x2=145 y2=191
# text: ""
DITL_300_Status Window DITL.txt
# 6 entries
# item 0: TEXT (0x88) disabled
# bounds: x1=174 y1=6 x2=389 y2=122
# text: ""
# item 1: ICON (0x20) enabled
# bounds: x1=42 y1=29 x2=106 y2=93
# ICON resource ID: 128
# item 2: TEXT (0x08) enabled
# bounds: x1=22 y1=100 x2=129 y2=116
# text: "InDisk‚Ñ¢ Ver 1.4"
# item 3: TEXT (0x08) enabled
# bounds: x1=5 y1=127 x2=151 y2=143
# text: "The Labeless-Labeler"
# item 4: TEXT (0x88) disabled
# bounds: x1=160 y1=127 x2=384 y2=143
# text: "Demo Sleeves Remaining to Print:"
# item 5: TEXT (0x88) disabled
# bounds: x1=385 y1=127 x2=409 y2=143
# text: ""
DITL_400_Nudge Setup DITL.txt
# 11 entries
# item 0: BUTTON (0x04) enabled
# bounds: x1=369 y1=190 x2=427 y2=210
# text: "OK"
# item 1: BUTTON (0x04) enabled
# bounds: x1=296 y1=190 x2=354 y2=210
# text: "Cancel"
# item 2: EDIT_TEXT (0x10) enabled
# bounds: x1=282 y1=118 x2=320 y2=134
# text: ""
# item 3: EDIT_TEXT (0x10) enabled
# bounds: x1=282 y1=143 x2=320 y2=159
# text: ""
# item 4: TEXT (0x88) disabled
# bounds: x1=219 y1=118 x2=278 y2=134
# text: "X Nudge:"
# item 5: TEXT (0x88) disabled
# bounds: x1=219 y1=143 x2=278 y2=159
# text: "Y Nudge:"
# item 6: TEXT (0x88) disabled
# bounds: x1=324 y1=118 x2=372 y2=134
# text: "Inches"
# item 7: TEXT (0x88) disabled
# bounds: x1=324 y1=143 x2=372 y2=159
# text: "Inches"
# item 8: TEXT (0x88) disabled
# bounds: x1=24 y1=15 x2=354 y2=65
# text: "If the printer output is not properly located on the sleeve, you may \"nudge\" the output to move it to an acceptable location on the sleeve: "